RM新时代官方-首页

　　在混凝土攪拌一體車使用過程中，如果液壓系統出現故障會使攪拌一體車的工作性能大大降低，車主朋友們只有了解了液壓系統的故障原因并及時排出故障才能使攪拌一體車恢復正常，今天收集了有關攪拌一體車液壓系統壓力不足或完全無壓力的原因、診斷和排除，供車主朋友們參考學習。

　　In the process of using the concrete mixer truck, if the hydraulic system fails, the working performance of the truck will be greatly reduced. Only when the owners understand the fault causes of the hydraulic system and timely eliminate and solve the fault, can the truck return to normal. Today, we collected the causes, diagnosis and treatment of insufficient or no pressure in the hydraulic system of the truck mixer Exclude, for car owners friends reference learning.

　　如果混凝土攪拌一體車出現液壓系統壓力不足或完全無壓力時，我們可以根據以下幾個方面依次進行排查：

　　If there is insufficient or no pressure in the hydraulic system of the concrete mixer truck, we can check it according to the following aspects:

　　查看液壓泵是否能輸出液壓油。如果是新的液壓泵，無液壓油輸出，可能是泵體有鑄造缺陷（縮孔、砂眼等），使吸油腔和壓油腔相通，失去壓油能力，應及時找廠家更換。若不是新的液壓泵，無液壓油輸出，則可能是泵的轉向不對，零件磨損嚴重或損壞，及時更換。

　　Check whether the hydraulic pump can output hydraulic oil. If it is a new hydraulic pump without hydraulic oil output, it may be that the pump body has casting defects (shrinkage cavity, sand hole, etc.), so that the oil suction chamber and the pressure oil chamber are connected, and the oil pressure capacity is lost, it should be replaced by the manufacturer in time. If it is not a new hydraulic pump and there is no hydraulic oil output, it may be that the steering direction of the pump is not correct and the parts are seriously worn or damaged. Replace them in time.
         

　　若液壓泵有油液輸出，查看溢流閥工作是否正常。若不正常，則可能是壓力油路中的某個閥有污物或其他原因卡住，處于回油位置，致使壓力油路與溢流回路短路，也可能是管接頭松脫，或處于壓力油路中的某些閥泄漏嚴重，或液壓缸、液壓馬達的密封損壞，嚴重泄漏。

　　If the hydraulic pump has oil output, check whether the relief valve works normally. If it is abnormal, it may be that a valve in the pressure oil circuit is stuck due to dirt or other reasons, and it is in the oil return position, resulting in a short circuit between the pressure oil circuit and the overflow circuit, or the loose pipe joint, or serious leakage of some valves in the pressure oil circuit, or the seal damage of the hydraulic cylinder and hydraulic horse.

　　排除方法：拆開有關閥進行清洗，檢查密封間隙的大小及各種密封裝置，密封裝置損壞應更換。

　　Troubleshooting: remove the relevant valve for cleaning, check the size of sealing clearance and various sealing devices, and replace the damaged sealing device.

　　若液壓泵輸出流量隨壓力升高而顯著減小，且壓力達不到規定值，則是由于液壓泵磨損后間隙增大所致。

　　If the output flow of the hydraulic pump decreases significantly with the increase of the pressure, and the pressure can not reach the specified value, it is due to the increase of the clearance after the wear of the hydraulic pump.

　　排除方法：測定液壓泵的容積效率，即可確定該泵是否能繼續使用，對磨損嚴重的零件，應進行修配或更換。

　　Exclusion method: determine the volume efficiency of the hydraulic pump, you can determine whether the pump can continue to use, the parts seriously worn should be repaired or replaced.

　　若整個液壓系統能建立正常壓力，而某些管路或液壓缸（或液壓馬達）中無壓力，則可能是由于管路、小孔或節流閥、換向閥等部位堵塞。此時，應逐段檢查壓力和有無油液通過，找出原因，加以排除。

　　If the whole hydraulic system can establish normal pressure, but there is no pressure in some pipelines or hydraulic cylinders (or hydraulic motors), it may be due to blockage of pipelines, orifices, throttle valves and directional valves. At this time, check the pressure and whether there is oil passing through section by section, find out the reason and eliminate it.

　　本文由混凝土攪拌一體車整理提供，希望對您有所幫助，如您想了解更多內容歡迎點擊我們的http://jackpetty.net網站。

　　This article is provided by the concrete mixer truck, hope to help you, if you want to know more, welcome to click our http://jackpetty.net Website.