RM新时代官方-首页

　　1. When the oil tank is worn and damaged and the automatic feeding mixer is in use, if oil leakage is found in the oil tank, the oil leakage can be wiped clean, and soap or gum can be used to coat the oil leakage to temporarily block it; epoxy resin adhesive is used to repair the oil tank, and the effect is better.

　　2.油管破裂油管破裂時可將破裂處擦干凈，涂上肥皂，用布條或膠布纏繞在油管破裂處，并用鐵絲捆緊，然后再涂上一層肥皂。

　　2. When the oil pipe breaks, clean the broken part, coat it with soap, wrap it with cloth or adhesive tape, tie it with iron wire, and then apply a layer of soap.

　　3.油管折斷油管折斷時可找一根與油管直徑適應的膠皮或塑料管套接。如套接不夠緊密，兩端再用鐵絲捆緊，防止漏油。

　　3. When the oil pipe is broken, a rubber or plastic pipe suitable for the diameter of the oil pipe can be used for sleeve connection. If the sleeve connection is not tight enough, both ends shall be bound with iron wire to prevent oil leakage.
            

　　4.水泥攪拌車缸蓋等部位出現砂眼而漏油、漏水可根據砂眼大小，選用相應規格的電工用保險絲，用手錘輕輕將其砸入砂眼內，即可防止漏油、漏水。

　　4. If there are sand holes in the cylinder head and other parts of the cement mixer truck, according to the size of the sand holes, the electrician's fuse of the corresponding specifications can be selected and gently smashed into the sand hole with a hammer to prevent oil leakage and water leakage.

　　5.油管接頭漏油攪拌車使用時，如發動機油管接頭漏油，多是油管喇叭口與油管螺母不密封所致?？捎妹藜喞p繞于喇叭下緣，再將油管螺母與油管接頭擰緊；還可將泡泡糖或麥芽糖嚼成糊狀，涂在油管螺母座口，待其干凝后起密封作用。也可將人造革或皮褲帶剪成型或放入孔中砸成型，安上即可，還可用一截塑料管剪開成型安上。

　　5. When the mixer truck is used, if the engine oil pipe joint leaks, it is mostly caused by the oil pipe bell mouth and the oil pipe nut are not sealed. Cotton yarn can be wound around the lower edge of the horn, and then the oil pipe nut and the oil pipe joint can be tightened; the bubble gum or maltose can be chewed into paste and coated on the seat of the oil pipe nut, which will play a sealing role after drying and setting. It can also be made of artificial leather or leather trousers by cutting or smashing it into holes. A section of plastic pipe can also be used for cutting and forming.

　　6.沉淀杯破裂用膠布管或塑料管把沉淀杯進出油管套上，使油不經過沉淀杯直通。

　　6. If the sedimentation cup is broken, sleeve the inlet and outlet pipes of the sedimentation cup with tape or plastic pipe, so that the oil does not pass through the sedimentation cup.

　　7.進、出水軟管破裂破裂不大時，可用涂有一層肥皂的布將漏水處包扎好；如破裂較大時，可將軟管破裂處切斷，在中間套上一個竹管或鐵管，并用鐵絲捆緊。

　　7. When the water inlet and outlet hose is not broken, the leaking part can be wrapped up with a layer of soap; if the rupture is large, cut off the broken part of the hose, put a bamboo pipe or iron pipe in the middle, and bind it with iron wire.

　　8.風扇皮帶斷裂可把斷了的皮帶用鐵絲串聯扎好或采用開開停停的辦法把車開走。

　　8. If the fan belt is broken, the broken belt can be tied in series with iron wire or the car can be driven away by using the method of start stop stop.

　　9.螺孔滑扣螺孔滑扣導致漏油或連桿松動，使其無法工作。這時可將原螺桿用錘子錘扁，使其兩邊膨脹變大，再緊固好，但不可多次拆卸，待下次保養時修理。

　　9. The screw hole sliding buckle causes oil leakage or the connecting rod is loose, which makes it unable to work. At this time, the original screw can be flattened with a hammer to enlarge the expansion on both sides, and then fasten it well. However, it can not be disassembled for many times, and it will be repaired in the next maintenance.

　　以上是關于自動上料攪拌車應急修車小竅門的介紹，希望對大家有所幫助，如您想要了解更多內容歡迎點擊我們的http://jackpetty.net網站。

　　The above is about automatic feeding mixer emergency repair tips, I hope to help you, if you want to know more, welcome to click our http://jackpetty.net Website.