RM新时代官方-首页

　　If the automatic feeding mixer is ordinary and does not pay attention to cleaning, it is very easy to stick to the tank. The following small make-up for you to analyze what is the reason.

　　在每次卸料之后，用罐車自己帶水槍對罐口、葉片、進料口、罐體以及犄角旮旯停止沖洗，防止混凝土熔化之后越積越多，不好清算。天天的輸送義務停止之后，在罐內加入1立方米以上的凈水，倏地的旋轉罐體停止蕩滌。有條件的公司，還能夠在罐內加入石子，效果會更好。在運營時隨時沖洗，收車之后徹底蕩滌罐車。

　　After each unloading, stop washing the tank mouth, blade, feeding port, tank body and corner with water gun to prevent the concrete from accumulating after melting, which is not easy to settle. After the daily delivery obligation stops, add more than 1 cubic meter of purified water into the tank, and then the rotating tank stops cleaning. Qualified companies can also add stones in the tank, and the effect will be better. Wash at any time during operation and thoroughly clean the tank car after collection.

　　自動上料攪拌車加水流程：控制氣壓，固禁接頭。罐體氣壓在出廠的時光已經設定好了，無需自己調節(jié)，假如出現特別情形須要自己調節(jié)，提議氣壓控制在3.5mpa閣下。

　　Water adding process of automatic feeding mixer: control the air pressure and forbid the joint. The tank air pressure has been set before leaving the factory, so it is not necessary to adjust it by yourself. In case of special circumstances, it is suggested that the air pressure should be controlled at 3.5Mpa.
           

　　由于原料差別，每一盤的混凝土品德都有些差別，裝好混凝土時，一定要檢查它的坍落度以及合易度，小心混凝土的提前熔化跟混凝土分層沉淀，以免運到現場后混凝土又不克不及投入運用，糟蹋人力物力時光。留心輸送的距離，可能造成混凝土品德改變，這個距離盡量控制在直徑30范圍以內。

　　Due to the difference of raw materials, the concrete quality of each plate is different. When installing the concrete, it is necessary to check its slump and workability. Be careful of the concrete melting in advance and the layered precipitation of concrete, so as to avoid that the concrete can not be put into use after being transported to the site, which will waste the manpower and material resources. Pay attention to the distance of conveying, which may cause the change of concrete quality. The distance should be controlled within the range of 30km in diameter.

　　攪拌車出車之前計劃好道路以及車輛通行情形，只管增加車輛在路上的時光。碰到人為或許不可抵抗的要素招致無法卸料時，隨時檢查罐內情形，一旦發(fā)現有混凝土開端熔化，應立即卸料，以免造成全部罐體的報廢。

　　Plan the road and the traffic situation before the mixer starts, just increase the time of the vehicle on the road. When it is impossible to unload due to man-made or irresistible factors, check the situation in the tank at any time. Once it is found that the concrete begins to melt, the material should be unloaded immediately, so as to avoid the scrapping of all the tanks.

　　以上就是有關自動上料攪拌車加重的原因及方法，想要了解更多請關注我們的網站http://jackpetty.net。

　　The above is about the reasons and solutions of automatic feeding mixer truck. For more information, please pay attention to our website http://jackpetty.net 。