概述：驅動安裝的作用是驅動混凝土貯罐轉動，它由取力器、萬向軸、液壓泵、液壓馬達、支配閥、液壓油箱及冷卻安裝組成。假如這局部因毛病中止工作
驅動安裝的作用是驅動混凝土貯罐轉動，它由取力器、萬向軸、液壓泵、液壓馬達、支配閥、液壓油箱及冷卻安裝組成。假如這局部因毛病中止工作，自上料混凝土攪拌車將不能轉動，這會招致車內混凝土報廢，嚴重的以使整罐混凝土凝結在罐內，形成自動上料混凝土攪拌車報廢。因而，驅動安裝能否牢靠是運用中必需高度注重的問題。為保證驅動安裝完好牢靠，
自上料攪拌一體車應做好以下維護工作：
The function of driving installation is to drive the concrete storage tank to rotate. It is composed of power take-off, universal shaft, hydraulic pump, hydraulic motor, control valve, hydraulic oil tank and cooling installation. If this part of the work is stopped due to defects, the self loading concrete mixer will not be able to rotate, which will lead to the scrapping of the concrete in the truck, and even cause the whole tank of concrete to coagulate in the tank, forming the scrapping of the automatic feeding concrete mixer. Therefore, it is necessary to pay more attention to whether the driving installation is reliable or not. In order to ensure that the drive is installed in good condition and reliable, the following maintenance work shall be done for the self feeding mixing truck:
1.萬向轉動局部是毛病多發部位，應按時加注光滑脂，并經常檢查磨損狀況，及時修理改換。車隊?wèi)?yīng)有備用的萬向軸總成，以保證一旦發作毛病能在幾非常鐘內恢復工作。
1. The universal rotation part is the part with frequent faults, so it is necessary to add smooth grease on time, check the wear condition frequently, and repair and replace it in time. The team should have spare cardan shaft assembly to ensure that once a fault occurs, it can resume work in a few minutes.
2.保證液壓油清潔。自動上料混凝土攪拌車工作環境惡劣，一定要避免污水泥沙進入液壓系統。液壓油要按運用手冊請求定期改換。一旦檢查時發現液壓油中混入水或泥沙，就要立刻停機清洗液壓系統、改換液壓油。
2. Ensure that the hydraulic oil is clean. The working environment of automatic loading concrete mixer is bad, so it is necessary to avoid dirty cement sand entering the hydraulic system. The hydraulic oil should be changed regularly according to the operation manual. Once it is found that the hydraulic oil is mixed with water or sediment, it is necessary to stop the machine immediately to clean the hydraulic system and change the hydraulic oil.
3.保證液壓油冷卻安裝有效。要定時清算液壓油散熱器，防止散熱器被水泥梗塞，檢查散熱器電動風扇運轉能否正常，避免液壓油溫度超標。液壓局部只需保證液壓油清潔，普通毛病不多；但消費廠家不同，運用壽命則不一樣。
3. Ensure that the hydraulic oil cooling installation is effective. It is necessary to clear the hydraulic oil radiator regularly to prevent the radiator from being blocked by cement, and check whether the electric fan of the radiator can run normally, so as to avoid the excessive temperature of the hydraulic oil. Hydraulic parts only need to ensure that the hydraulic oil is clean, and there are not many common problems, but the service life of different manufacturers is different.
The above is about the self loading concrete mixer driver installation how to maintain, hope to help you, if you want to understand more information content, welcome to click the website: self loading mixing truck http://jackpetty.net 。
點擊撥打服務熱線：4008791999
